激光溅射Ni等离子体与气相CH3OH团簇的反应

用激光溅射 分子束技术研究了气相中Ni的等离子体与甲醇分子团簇的反应 .观察到Ni+ (CH3 OH) n、NiO+ (CH3 OH) n、H+ (CH3 OH) n、H3 O+ (CH3 OH) n 四个种类的团簇正离子和CH3 O-(CH3 OH) n(n≤ 2 5 )一种团簇负离子 .详细考察了激光烧蚀等离子体作用于脉冲分子束的不同位置时 ,对团簇产物种类和团簇尺寸大小的影响 .发现NiO+ (CH3 OH) n 是由Ni+ (CH3 OH) n 团簇内的脱甲烷反应生成的 ,而H+ (CH3 OH) n、H3 O+ (CH3 OH) n主要是激光等离子体中的电子与甲醇团簇碰撞电离产生的     

Microstructure and high-temperature wear resistance of a laser surface alloyed γ-TiAl with carbon

TiC reinforced composite coating on γ-TiAl alloy was successfully fabricated by laser surface alloying with carbon. The fine TiC reinforcing phase had a gradient distribution in the coating, and its growth morphology of TiC in laser surface alloyed coating was in unique faceted platelet-like. The composite coating exhibited high hardness and excellent high-temperature sliding wear resistance.     

氯柱硼镁石在氯化镁水溶液中相转化平衡液相的红外光谱分析

采用差示FTIR光谱技术,研究了氯柱硼镁石在30℃下浓度为0.5,12和18％MgCl_2水溶液中溶解及相转化平衡饱和水溶液中硼氧配阴离子的FTIR光谱。给出了溶液中硼氧配阴离子的FTIR光谱振动频率的归属,515cm~(-1)为单和二硼氧配阴离子特征峰,630cm~(-1)为三硼氧配阴离子特征峰,550cm~(-1)为四硼氧配阴离子特征峰。对饱和水溶液中硼氧配阴离子的存在形式及其相互作用以及与相转化析出固相的关系进行了讨论。     

Si微电阻桥温度分布与热传导特性的显微Raman光谱研究

采用显微Raman光谱方法对红外目标模拟器中重掺杂Si微电阻桥单元的热传导特性进行研究，根据Si桥的实际特性建立相应的Raman散射模型，通过测量Raman峰位的移动得到高功率激光辐照下测量点的温度.对Si桥桥面分别进行了沿某些特殊线段的逐点线扫描和覆盖全部桥面的面扫描，得到各点的温升及其分布.用基于有限元分析的软件结合Si桥结构参数对各测量点的温升进行了模拟计算，其结果在热导分布的基本趋势上与实验相一致.实验细致地揭示了热导分布的局域起伏，反映出实际器件的不均匀性，为改进器件设计、优化器件性能提供了实验依据. 关键词： Raman光谱 Si桥 温度分布 热导     

Structural manipulation of pyrochlores: Thermal evolution of metastable Gd2(Ti1−yZry)2O7 powders prepared by mechanical milling

The structural and microstructural characteristics of metastable Gd₂(Ti_1−yZr_y)₂O₇ powders prepared by mechanical milling have been studied by a combination of XRD and Raman spectroscopy. Irrespective of their Zr content, as-prepared powder phases present an anion-deficient fluorite-type of structure as opposed to the pyrochlore equilibrium configuration obtained for the same solid solution by other synthetic routes. These fluorites are stable versus thermal activation, at least up to temperatures of 800 °C. For the Ti-rich compositions, thermal treatments at higher temperatures facilitate the rearrangement of the cation and anion substructures and the relaxation of mechanochemically induced defects whereas for compositions with high Zr content, the fluorite crystal structure is retained even at temperatures as high as 1200 °C. Interestingly enough, transient pyrochlores showing a very unusual cation distribution were observed during the thermally induced defect-recovery process.     

氟化类金刚石薄膜的拉曼和红外光谱结构研究

关键词：     

Possible spectroscopic manifestation of the angular group induced bond alteration (AGIBA) effect in toluene

The most obvious consequence of the concept of aromaticity is the common confidence that in aromatic compounds, bond lengths do not alternate and are between typical to the single and double ones. However, in 1994, performing crystal structure investigations of substituted pyridines and their salts, Krygowski and co‐workers have discovered a very surprising angular group induced bond alteration (AGIBA) effect: It appears that some angular substituents, like methoxy or nitrozo groups, can induce bond alternation in aromatic rings. Crystal studies do not allow one to operate with liquids that are more common in organic chemistry. This paper presents the first possible evidence of spectroscopic manifestations of the AGIBA effect. Raman spectra of the liquid toluene are analyzed. It is found that instead of being single, the line corresponding to the ring breathing vibrations is clearly split by 1.0–1.4 cm^?1, thus indicating the presence of two (cis‐ and trans‐) AGIBA isomers. The energy difference between these isomers estimated in temperature dependent Raman studies is found equal to 6.68 kJ mol^?1. The low‐wavenumber line therefore corresponds to the cis‐AGIBA isomer and the high‐wavenumber line to the trans‐AGIBA isomer stabilized by the AGIBA effect. Copyright © 2007 John Wiley & Sons, Ltd.     

Investigating laser rapid manufacturing for Inconel-625 components

This paper presents an investigation of laser rapid manufacturing (LRM) for Inconel-625 components. LRM is an upcoming rapid manufacturing technology, it is similar to laser cladding at process level with different end applications. In general, laser-cladding technique is used to deposit materials on the substrate either to improve the surface properties or to refurbish the worn out parts, while LRM is capable of near-net shaping the components by layer-by-layer deposition of the material directly from CAD model. In the present study, a high-power continuous wave (CW) CO₂ laser system, integrated with a co-axial powder-feeding system and a three-axis workstation were used. The effect of processing parameters during LRM of Inconel-625 was studied and the optimum set of parameters for the maximum deposition rate was established employing Orthogonal L9 array of Taguchi technique. Results indicated that the powder feed rate and the scan speed contributed about 56% and 26%, respectively to the deposition rate, while the influence of laser power was limited to 10% only. Fabricated components were subjected to non-destructive testing (like—ultrasonic testing, dye-penetrant testing), tensile testing, impact testing, metallographic examinations and micro-hardness measurement. The test results revealed defect-free material deposition with improved mechanical strength without sacrificing the ductility.     

Bohr-Mottelson转动谱公式参数之间的新关系式

在利用Harris两参数公式研究Bohr-Mottelson转动谱公式参数之间的关系的基础上,改用Harris三参数公式,并由此提出了Bohr-Mottelson转动谱公式参数之间的新关系式,进而用I(I+1)四参数展开式计算了A～60,80,130,140,150,190区超形变偶偶核的基带和锕系和稀土区正常形变核基带,讨论了参数之间的关系,发现新关系式与实验较好地符合.